| Official Luthiers Forum! http://www-.luthiersforum.com/forum/ |
|
| Sanders - Your Favorite http://www-.luthiersforum.com/forum/viewtopic.php?f=10102&t=5118 |
Page 1 of 1 |
| Author: | GregG [ Thu Feb 16, 2006 3:02 am ] |
| Post subject: | |
I was wondering what sanders you guys found the most valuable for guitar building. Other than drum sanders do you use any other floor type sander, edge sander, oscilating sander, etc. If so what brand and type do you use. Or is the old hand sander and elbow grease that gets the job done. Thanks, Greg |
|
| Author: | Michael Dale Payne [ Thu Feb 16, 2006 3:17 am ] |
| Post subject: | |
Hand held pneumatic drum is my absolute favorite sander |
|
| Author: | Michael Dale Payne [ Thu Feb 16, 2006 3:33 am ] |
| Post subject: | |
I think I have a link. let me look but mine is not the Grizly but very simular |
|
| Author: | Michael Dale Payne [ Thu Feb 16, 2006 3:49 am ] |
| Post subject: | |
www.sand-rite.com/touchup.html |
|
| Author: | RussellR [ Thu Feb 16, 2006 4:19 am ] |
| Post subject: | |
Random orbitol Sander is very useful I also have a bench mounted Disc and Belt Sander which I have only had a while but find very useful. |
|
| Author: | John How [ Thu Feb 16, 2006 4:44 am ] |
| Post subject: | |
Lots of sanders 12" disc (Grizz) 46" belt (wood tech) Oscilating spindle (Ryobi) Drum/thickness 16/32 (Ryobi) handheld pneumatic 1 1/2" (Grizz) RO (Dewalt) RO (PC) various sized palm sanders Motorized 24" dish with 24 ft & 15 ft radius for profiling sides. (homemade) Favorite sander is a 2 1/2"x4" piece of hard foam rubber, just slightly flexible that I worry I'll loose one of these days. Oh and I'm building a low speed (200-300 rpm) horizontal disc (8" dia plate glass) sander to be used as a motorized "Scary Sharp" system for my chisels and other assorted blades. |
|
| Author: | Chas Freeborn [ Thu Feb 16, 2006 5:19 am ] |
| Post subject: | |
I just got a flyer from Sand Rite- they've got a luthiers special on the hand held pneumatic drum. 10% off. I guess they've been listening... Great company too. My other favorite finishing sander is the Nitto LS-10. It's a little straight line sander. Very light and controlable and no swirl marks. Expensive, but a premium quality tool. -C |
|
| Author: | npalen [ Thu Feb 16, 2006 10:00 am ] |
| Post subject: | |
Disc sander This little guy is expensive but very nice with it's low and adjustable rpm. Eliminates burning while sanding small parts such as nuts. Nelson |
|
| Author: | Alain Desforges [ Thu Feb 16, 2006 10:10 am ] |
| Post subject: | |
Wow Nelson, that's a nice one! I use a 5 inch random orbital that I like a lot. I also have a bench mounted belt sander with the 6 inch disk on there. Very useful. I often reach for my trusty Lee Valley sanding block, though. Tough to beat old school quality. My next will probably be an edge sander and hopefully a dual drum thickness sander.... |
|
| Author: | A Peebels [ Thu Feb 16, 2006 11:21 am ] |
| Post subject: | |
I use a Rigid oscillating belt/drum sander, a performax 10-20 thickness sander, a Porter cable hand held belt sander, a Porter cable DA sander, a Jet 6x48 belt sander, and 100,000 self made sanding blocks for hand sanding. Al |
|
| Author: | Serge Poirier [ Thu Feb 16, 2006 3:37 pm ] |
| Post subject: | |
Home made drum sander here! |
|
| Author: | Colin S [ Thu Feb 16, 2006 9:24 pm ] |
| Post subject: | |
I use 4 sanders that are indispensible. 1. DeWalt ROS 2. Bench Linisher/disc sander combo And two in the drill press, 3. Large bobbin sander 6" x3" 4. 5" disc sander (used for thicknessing) after the SafeT planer. I recently sold my 16-32 as it wasn't being used. Colin |
|
| Author: | L. Presnall [ Fri Feb 17, 2006 1:56 am ] |
| Post subject: | |
Michael, how much CFM do these type sanders require? I only have a small pancake compressor and it's not worth my going to a huge one just for one or two tools...but I've daydreamed about a "rolling pin" sander for some time... |
|
| Author: | Michael Dale Payne [ Fri Feb 17, 2006 3:13 am ] |
| Post subject: | |
Larry my air tool is a C&H die grinder I believe at max it uses 5cmf at 90 psi but I don't run it full often and never on the sanding drum. I run the tool at 60 psi and turn down the rpms adjustment on my grinder about half way. I don't hog material with it. In fact I use it with a pretty light touch. You can use this drum with a cordless drill if you wanted. I am sure with a pancake you would be short intermitting use only depending on the rotary air tool you use. |
|
| Page 1 of 1 | All times are UTC - 5 hours |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|